<tr id="fumjy"><input id="fumjy"><small id="fumjy"></small></input></tr>

  • <tr id="fumjy"></tr>
    <ol id="fumjy"></ol>

    <big id="fumjy"></big>

    <big id="fumjy"></big>
  • <legend id="fumjy"></legend>
    1. <legend id="fumjy"><sup id="fumjy"></sup></legend>
      中文
      + 更多 聯系我們
      聯系我們

      蘇州威旻達機械設備有限公司

      聯系人:王經理

      手機:15906136866

      電話:0512-68136800

      傳真:0512-68136800

      地址:蘇州市吳中區吳中大道5399號 

      行業資訊

      要把中空玻璃設備的作用發揮

      2018-01-31 點擊數:901
      1、首先要檢查中空玻璃加工設備水箱里的水充足,然后打開水泵,調整白色海綿輥上方的噴水管,保證海綿輥所有位置都能被沖洗到。然后用手將海綿輥上的雜質和臟物清洗干凈,并且保證海綿輥被完全泡開泡膨脹。注意在冬天開啟中空玻璃生產線時,一定不要先打開清洗傳送。因為冬天兩個緊鄰的海綿輥會被凍在一起,在沒有被浸泡開的情況下打開傳送,會導致海綿輥被撕壞。
      1, first of all, check the water in the tank of the insulating glass processing equipment, then open the water pump and adjust the spray pipe above the white sponge roller to ensure that all positions of the sponge roller can be washed. Then the impurities and dirt on the sponge roll are cleaned with hand, and the sponge roll is completely bubbling and swollen. Be careful not to open the cleaning transmission first when the hollow glass production line is opened in the winter. Because the two adjacent sponge rolls are frozen together in the winter and open without being soaked, it will cause the spongy roll to be torn out.
      2、然后打開清洗傳送,將待加工的中空玻璃放在傳送輪上,注意玻璃一定要放平穩,防止玻璃在傳送過程中掉落傷到人。

      2, then open the cleaning transmission, put the processed insulating glass on the transport wheel, and notice that the glass must be kept stable, so as to prevent the glass from falling to the human in the process of transmission.

      鋁切割設備

      3、鋁隔條上涂抹的丁基膠要保證均勻,而且涂抹在整個鋁條表面,防止漏膠,有毛刺現象。并且采用優質丁基膠保證鋁條和玻璃結實的站合在一起。鋁隔條涂完膠后禁止有粘上灰塵。
      3, the butyl rubber coated on the aluminum strip should be uniform and smeared on the surface of the whole aluminum strip to prevent leakage and burr. And the use of high quality butyl rubber to ensure that the aluminum bar and the sturdy glass station together. After the aluminum strip is coated with glue, it is forbidden to stick to the dust.
      4、雙組份密封膠要涂抹牢固,表面保持平滑,尤其是拐角處要涂抹好,防止漏氣,跑氣現象。
      4, the double component sealant should be smeared firmly, the surface is smooth, especially the corner should be smeared well to prevent gas leakage and gas running.
      一旦發現中空玻璃設備出現問題要及時進行處理,保證設備達到“整潔、清潔、潤滑、安全”四項要求。在保養設備的過程中,以下幾點需要特別注意:
      Once the problem of insulating glass equipment is found to be dealt with in time, four requirements of "clean, clean, lubricated and safe" are guaranteed. In the process of maintenance of the equipment, the following points should be paid special attention to:
      1、丁基膠涂布機的皮帶上撒滑石粉
      1, sow powder on the belt of butyl rubber coating machine
      2、生產線的鏈條 齒輪經常上油
      2. The chain gear of the production line is often oil
      3、玻璃是磨邊過的,不然會損傷傳動輪
      3, the best glass is to wear the edge, or it will damage the drive wheel.