<tr id="fumjy"><input id="fumjy"><small id="fumjy"></small></input></tr>

  • <tr id="fumjy"></tr>
    <ol id="fumjy"></ol>

    <big id="fumjy"></big>

    <big id="fumjy"></big>
  • <legend id="fumjy"></legend>
    1. <legend id="fumjy"><sup id="fumjy"></sup></legend>
      中文
      + 更多 聯系我們
      聯系我們

      蘇州威旻達機械設備有限公司

      聯系人:王經理

      手機:15906136866

      電話:0512-68136800

      傳真:0512-68136800

      地址:蘇州市吳中區吳中大道5399號 

      常見問題

      鋁型材切機下料應該注意的問題

      2018-05-09 點擊數:1404
          為了保證鋁型材產品在切割過程的質量,我們在使用鋁型材切割機下料時,該注意以下幾點:
          In order to ensure the quality of aluminum products in the cutting process, we should pay attention to the following points when using aluminum profile cutting machine.
          1、下料夾緊時應夾在有內筋支撐的部位以保證切割角度,定位夾緊平行、準確、穩定,型材底部與定位平臺之間嚴密無間隙;

          when the material is clamped, it should be clamped in the position of the inner reinforcement to ensure the cutting angle, and the positioning and clamping are parallel, accurate and stable, and the bottom gap between the bottom of the profile and the positioning platform is close.

      鋁切割設備

          2、保證合理的切割進給速度,整個切割過程控制在8~10秒內完成為宜,回程速度可稍快;
          ensure reasonable cutting feed speed, the whole cutting process is controlled within 8~10 seconds, and the return speed can be slightly faster.
          3、保證切割鋸表面清潔無異物;
          Ensure that the surface of the cutting saw is clean and free of foreign objects.
          4、每批次切割完成,應作首件檢驗,檢查其切割長度和角度以及內角方向,以后每切斷20根成品檢查一次;
          For each batch of cutting, the first piece inspection shall be made, and the cutting length and angle and the direction of the inner corner shall be checked. After that, 20 pieces of finished products will be checked once every time.
          5、切割完成工件應保持切割部位清潔,不得被水、油、灰塵等污染;
          After cutting, the workpiece should be kept clean and not contaminated by water, oil and dust.
          6、型材表面應光滑,不允許有裂痕等及影響使用的雜質;
          The surface of the profile should be smooth without cracks and other impurities.
          7、及時清除定位臺面上的邊角廢料和碎屑雜物;
          remove the corner scrap and debris debris on the positioning table in time.
          8、鋸切完畢的型材,及時用空壓氣將型材腔內的碎屑雜物清除到廢料箱中,確保型材腔體的清潔;
          After cutting the profiles, remove debris debris from the section cavity with air pressure to ensure that the cavity of the section is clean.
          9、下料后的產品構件應按每工程、規格、數量進行堆放,并分層用軟質材料墊襯,避免型材表面受損,或擺放在下道工序的托架上。
          The product components after the blanking should be stacked on each project, specification and quantity, and layered with soft material padding to avoid the damage to the surface of the profile or placed on the bracket of the next process.